Free shipping on all orders over $50
7-15 days international
28 people viewing this product right now!
30-day free returns
Secure checkout
87834233
MacBook Pro Full Kit Set - Feet with Outer + Inner Plugs + Adhesive, Screws + Screwdriver DIY Foot Replacement Instructions Note: Use the foot replacement kit for missing feet only. Do not replace well-adhered feet. Removing feet for the sake of replacement can damage the bottom case. Tools Needed to Complete Repair: Phillips 00 screwdriver Tweezers Paper clip or safety pin Gloves are suggested for this procedure. Preliminary Step Before you begin, check the foot location requiring replacement and verify that the case plug, and the case foot in the kit, match the pictures below. Place the computer upside down on a clean, lint-free cloth or other nonabrasive surface. Remove the bottom case. Using the Phillips 00 screwdriver, remove the bottom case by removing 10 screws. Important: Screws at sides and front must be removed and installed at an angle. Gently pull the bottom case from the side the display hinges are on and lift upwards at an angle. Make sure the foot area on the bottom case is clean and free of debris. If any portion of the foot adhesive remains, peel it up with a pair of tweezers. Clean both sides of the bottom case around the foot area. Allow the alcohol to evaporate. Peel the outer foot from its packaging and affix it firmly to the bottom case. Do not use the glue to adhere the outer foot to the bottom case. Avoid touching the adhesive backing. Use a paperclip or safety pin to open the glue nozzle. A paperclip or safety pin can also unplug the glue nozzle after storage. Apply a very small drop of glue on the bottom of the foot on the inner bottom case. Do not spread the glue. Seat the plug onto the glued area. Do not use your finger to press the foot plug down. Use the wooden end of a cotton swab to press the foot plug into place. Lightly press and hold the foot in place for 30 seconds. Clean any excess glue with a cotton dry swab. Important: Do not wipe the glue; use the cotton dry swab to absorb any excess glue. Excess puddled glue may take hours to dry and may cause the bottom case to adhere to the logic board or interior cabling. Using a timer, allow the glue to set for at least 60 minutes before applying the foot plug cover over the foot plug. Important: If laser etching is visible by the foot area, do not use the foot plug cover. Laser etching will normally be found on the left-rear foot area. Reassembly Note: Install screws in order shown. If sequence is not followed, bottom case might wobble when placed on level surface. SAFETY INSTRUCTIONS: GLUE IS AN EYE AND SKIN IRRITANT. GLUE BONDS TO SKIN INSTANTLY. Contains ethyl cyanoacrylate. Avoid contact with skin and eyes. If eye or mouth contact occurs, hold eyelid or mouth open and rinse thoroughly but gently with water only for 15 minutes and GET MEDICAL ATTENTION.Liquid glue will sting eye temporarily. Solidified glue may irritate eye like a grain of sand and should be treated by an eye doctor. If skin bonding occurs, soak in acetone-based nail polish remover or warm soapy water and carefully peel or roll skin apart (do not pull). Contact through clothing may cause skin burn. If spilled on clothing, flush with cold water. Avoid prolonged breathing of vapors. use with adequate ventilation. KEEP OUT OF THE REACH OF CHILDREN. Place the computer upside down on a clean, lint-free cloth or other nonabrasive surface. Remove the bottom case. Using the Phillips 00 screwdriver, remove the bottom case by removing 10 screws. Important: Screws at sides and front must be removed and installed at an angle. Gently pull the bottom case from the side the display hinges are on and lift upwards at an angle. Make sure the foot area on the bottom case is clean and free of debris. If any portion of the foot adhesive remains, peel it up with a pair of tweezers. Clean both sides of the bottom case around the foot area. Allow the alcohol to evaporate. A paperclip or safety pin can also unplug the glue nozzle after storage. Apply a very small drop of glue on the bottom of the foot on the inner bottom case. Do not spread the glue. Seat the plug onto the glued area. Use the wooden end of a cotton swab to press the foot plug into place. Lightly press and hold the foot in place for 1 min. Use the cotton dry swab away excess glue. Reassembly Note: Install screws in order shown. If sequence is not followed, bottom case might wobble when placed on level surface.
This kind of rubber feet are fit for macbook PRO Retina mac 13 mac 15 A1425 A1502 A1398 ONLY ,not for AIR ONES( A1370 A1369 A1465 A1466 ) PRO ONES(A1278 A1286 A1297)
High Quality 3M Adhesive The glue that binds the rubber to your MacBook pro rubber feet has to be taken as the first priority, as that is a direct indicator of the quality of the Macbook bottom pads. This is why Infinite Products provides the rubber feet with 3M adhesive glue, to ensure the best quality and to endure rough use.
Package includes 10 Piece Bottom Case Screws - 1 Pentalobe Screwdriver - 4 retina feet
Long-term use You can use these Macbook Pro feet replacement pads for a good number of years. As OEM is guaranteed and the quality is high, these Macbook bottom pads will not let you down several years down the line.
